Desktop 3D Printers
UP Mini 3D Printer - Now in stockIn Stock as at 20 October
Introducing the UP Mini 3D Printer, the much anticipated follow-up, to their highly acclaimed, flagship 3d printer, the UP! Plus. The all-new UP Mini 3D... More
3D Printer Parts and Accessories
Linear Bearing to suit 8mm shaftOn special - HALF PRICE! This linear bearing helps the axis to move freely and precisely.
Has a 15mm Outer Diameter, takes an 8mm shaft. It is 24mm long
The body has two grooves, 1.1mm ... More
Stepper Motor - Nema 17 - 1.8 degree stepsThis stepper motor is the standard for RepRaps and many of their derivatives.
Specifications:
1.8 degree step angle
4 wire, 300mm, no connector
Holding Torque of 4800 g-cm ... More
T2.5 x 5mm Belt, by the meterT2.5mm pitch belt, order by the meter, supplied as one continuous length up to 50m.
More
Heated Bed PCB - Version 2 - 214 x 214mmThis heated bed is needed to print ABS reliably. It works very well surfaced with Kapton (Polyamide) Tape, sticking when hot, but releasing your printed object once cooled. This is also needed for PLA... More
Plastic turntable with feet - 6 inchThis plastic turntable is good for holding a spool of filament, regardless of size and width. It measures 150mm across and is fitted with 6 bump-on rubber feet on each side to reduce the change of things moving around.
More
RAMPS Sandwich - Mega2560 Rev1, RAMPS1.4, 4xStepper Drivers and Mechancial End Stop KitBuy the major electronics componants together in this sandwich kit. Minimal soldering required
1 x Arduino Mega 2560 Processor Board (Revision 1, fully assembled)
1 x RAMPS 1.4 Main Boar... More
Arduino Mega 2560 - Rev1This fully assembled Board includes the processor, memory and interfaces you can use of a variety of projects. This is the Rev1 board, at a reduced price. It includes a USB cable
Microcontrolle... More
Arduino Controllers and Boards
Arduino Mega 2560 - Rev1This fully assembled Board includes the processor, memory and interfaces you can use of a variety of projects. This is the Rev1 board, at a reduced price. It includes a USB cable
Microcontrolle... More
Motors
Stepper Motor - Nema 17 - 1.8 degree stepsThis stepper motor is the standard for RepRaps and many of their derivatives.
Specifications:
1.8 degree step angle
4 wire, 300mm, no connector
Holding Torque of 4800 g-cm ... More
Hand Tools
Plastic turntable with feet - 6 inchThis plastic turntable is good for holding a spool of filament, regardless of size and width. It measures 150mm across and is fitted with 6 bump-on rubber feet on each side to reduce the change of things moving around.
More
Measurement and Testing
Infrared Thermometer with laser sighting and backlightThis thermometer can tell you the temperature of an object just by pointing the device at it, and pulling the trigger. Has a switchable laser pointer, so you know what you are measuring (the measured ... More
Mechanical Parts
Linear Bearing to suit 8mm shaftOn special - HALF PRICE! This linear bearing helps the axis to move freely and precisely.
Has a 15mm Outer Diameter, takes an 8mm shaft. It is 24mm long
The body has two grooves, 1.1mm ... More
T2.5 x 5mm Belt, by the meterT2.5mm pitch belt, order by the meter, supplied as one continuous length up to 50m.
More
Linear Bearing Block, 8mm shaft, AluminiumThese linear bearing blocks hold two LM8UU bearings with a grease nipple in between. They are 58 mm long, 34 mm wide and 22mm high. 4 mounting holes are 42 x 24mm apart, 3.4mm dia. through, and tapped... More
CAM Software
Mach 3 Software - Electronic DeliveryMach3 is widely accepted and supported software for controlling CNC machines large and small.
Converts a standard PC to a fully featured, 6-axis CNC controller
Visual Gcode display
... More